UNO R3 Bluetooth Android Project Starter Kits HC-05 for Arduino Beginner

UNO R3 Bluetooth Android Project Starter Kits HC-05 for Arduino Beginner
UNO R3 Bluetooth Android Project Starter Kits HC-05 for Arduino Beginner UNO R3 Bluetooth Android Project Starter Kits HC-05 for Arduino Beginner UNO R3 Bluetooth Android Project Starter Kits HC-05 for Arduino Beginner


Get UNO R3 Bluetooth Android Project Starter Kits HC-05 for Arduino Beginner


Description:

This kit has all the basic components for learning various Arduino input/output signals which you can later send and receive through your Android smartphone or computer.

Package Included:

1 x UNO R3 + USB Cable
1 x HC-05 Bluetooth Module
1 x Ultrasonic Range Sensor
1 x SG90 Tower Pro Servo + Arms + Skrews
1 x 1K Potentiometer
65 x Breadboard Jumper Wires
10 x 220ohm Resistor
1 x Piezo Buzzer
1 x Slide On-Off Switch
1 x 9V Battery Connector and Barrel Jack
2 x 5MM RGB (red green blue) LED
2 x 5MM Signal Red LED
2 x 5MM Signal Yellow LED
2 x 5MM Signal Green
2 x Breadboard Push Button
1 x SYB170 170-Point Solderless Breadboard






















UNO R3 Bluetooth Android Project Starter Kits HC-05 for Arduino Beginner See detail


Popular posts from this blog

SPH0645 I2S MEMS Microphone Sensor Board SPH0645LM4H 1.6-3.6V For Arduino Raspberry Pi

Image
Get SPH0645 I2S MEMS Microphone Sensor Board SPH0645LM4H 1.6-3.6V For Arduino Raspberry Pi Description:   The microphone is a single mono element. You can select whether you want it to be on the Left or Right channel by connecting the Select pin to power or ground. If you need stereo, pick up two microphones!  You can set them up to be stereo by sharing the Clock, WS and Data lines but having one with Select to ground, and one with Select to high voltage. This I2S MEMS microphone is bottom ported, so make sure you have the hole in the bottom facing out towards the sounds you want to read. It's a 1.6-3.6V max device only, so not for use with 5V logic (its really unlikely you'd have a 5V-logic device with I2S anyways).  Many beginner microcontroller boards don't have I2S, so make sure its a supported interface before you try to wire it up! This microphone is best used with Cortex M-series chips like the for Arduino Zero, for Feathe...
Read more

QF1021-A-10M 0-10Min Adjustable 220V Time Delay Relay Module Timer Delay Switch Timed Off with Overcharge Protection

Image
Get QF1021-A-10M 0-10Min Adjustable 220V Time Delay Relay Module Timer Delay Switch Timed Off with Overcharge Protection Features:   - Relay load capacity up to 10A250V - 3W metal oxide film resistor, withstand voltage - Double Zener to improve stability - Using single chip delay, time precision - QF1021-A-10M: (Time out -off) Turns on immediately after power-on, the delay is automatically disconnected, up to 10 minutes   Specifications:   Delay adjustment resolution: 100 levels, that is, the minimum range of 100 minutes can be adjusted to 1 minute, 1 minute per division. Delay error: 2% Standby power consumption: 1.0W Load capacity: 10A250V (General motor can be connected to 800W or less, please take the starting current as the standard) PCB size: 58mm * 43mm, height <20mm   Applications:   Home appliances, lighting delay modification, factory equipment delay control.   Warmly Noted:   The whole board is equipped with 220V voltage....
Read more

2.4 Inch TFT LCD Color Screen Module With Touch IC SD ILI9341 Card Display For Development Board

Image
Get 2.4 Inch TFT LCD Color Screen Module With Touch IC SD ILI9341 Card Display For Development Board Feature: Working voltage: 3.3V Resolution: 240x320 Working temperature: -30~85°C Interface: 16/8 parallel port communication Driver IC: ILI9341 Touch method: Resistive Package includes: 1 x 2.4 Inch TFT LCD Color Screen Module 2.4 Inch TFT LCD Color Screen Module With Touch IC SD ILI9341 Card Display For Development Board See detail
Read more