Plantower® Sensor Test Board Measure PM2.5 Gas Formaldehyde Carbon Dioxide and Other Integrated Sensors Module

Plantower® Sensor Test Board Measure PM2.5 Gas Formaldehyde Carbon Dioxide and Other Integrated Sensors Module
Plantower® Sensor Test Board Measure PM2.5 Gas Formaldehyde Carbon Dioxide and Other Integrated Sensors Module Plantower® Sensor Test Board Measure PM2.5 Gas Formaldehyde Carbon Dioxide and Other Integrated Sensors Module Plantower® Sensor Test Board Measure PM2.5 Gas Formaldehyde Carbon Dioxide and Other Integrated Sensors Module


Get Plantower® Sensor Test Board Measure PM2.5 Gas Formaldehyde Carbon Dioxide and Other Integrated Sensors Module


Feature:

For sensor testing, easy to operate, fast and easy
 
Testable sensor types:
 
Testable sensor types
Plantower PM2.5 Series Sensors
Plantower DS-HCHO-10 Formaldehyde Sensor
Plantower DS-CO2-20 Carbon Dioxide Sensor
Plantower PTQS1005 5-in-1 Sensor

Package includes:

1 x Sensor Test Board (not includes any sensors)




















Plantower® Sensor Test Board Measure PM2.5 Gas Formaldehyde Carbon Dioxide and Other Integrated Sensors Module See detail


Popular posts from this blog

QF1021-A-10M 0-10Min Adjustable 220V Time Delay Relay Module Timer Delay Switch Timed Off with Overcharge Protection

Image
Get QF1021-A-10M 0-10Min Adjustable 220V Time Delay Relay Module Timer Delay Switch Timed Off with Overcharge Protection Features:   - Relay load capacity up to 10A250V - 3W metal oxide film resistor, withstand voltage - Double Zener to improve stability - Using single chip delay, time precision - QF1021-A-10M: (Time out -off) Turns on immediately after power-on, the delay is automatically disconnected, up to 10 minutes   Specifications:   Delay adjustment resolution: 100 levels, that is, the minimum range of 100 minutes can be adjusted to 1 minute, 1 minute per division. Delay error: 2% Standby power consumption: 1.0W Load capacity: 10A250V (General motor can be connected to 800W or less, please take the starting current as the standard) PCB size: 58mm * 43mm, height <20mm   Applications:   Home appliances, lighting delay modification, factory equipment delay control.   Warmly Noted:   The whole board is equipped with 220V voltage....
Read more

Low Voltage MOSFET Switch Module Electronic 3V 5V Low Control High Voltage 12V 24V 36V FET Module

Image
Get Low Voltage MOSFET Switch Module Electronic 3V 5V Low Control High Voltage 12V 24V 36V FET Module Description:   Input control voltage: 3.3V-12V Output charging voltage: 5-36V The board is optically isolated and completely separate from the 2-terminal voltage. The input is controlled by a 2-pin control and the ground control can be connected directly to the control switch. Control current 1-5MA control voltage is different, the current difference is mainly the loss on the LED. Charging large current: 22A, more than 5A need to add a heat sink. Host input and output screw terminal block The control terminal uses a 2.54MM pin for easy wiring. Control can be directly connected to the microcontroller IO. The MCU can control the motor speed with the ARDUINO PWM. Light brightness, etc. Please note that high currents require the addition of an additional heat sink Board size: 4.2 × 2.6 cm Package includes: 1 x MOSFET Switch Module Low Vol...
Read more

SPH0645 I2S MEMS Microphone Sensor Board SPH0645LM4H 1.6-3.6V For Arduino Raspberry Pi

Image
Get SPH0645 I2S MEMS Microphone Sensor Board SPH0645LM4H 1.6-3.6V For Arduino Raspberry Pi Description:   The microphone is a single mono element. You can select whether you want it to be on the Left or Right channel by connecting the Select pin to power or ground. If you need stereo, pick up two microphones!  You can set them up to be stereo by sharing the Clock, WS and Data lines but having one with Select to ground, and one with Select to high voltage. This I2S MEMS microphone is bottom ported, so make sure you have the hole in the bottom facing out towards the sounds you want to read. It's a 1.6-3.6V max device only, so not for use with 5V logic (its really unlikely you'd have a 5V-logic device with I2S anyways).  Many beginner microcontroller boards don't have I2S, so make sure its a supported interface before you try to wire it up! This microphone is best used with Cortex M-series chips like the for Arduino Zero, for Feathe...
Read more