3pcs 3-color Full Color LED SMD Module Board KY-009 5050 For Arduino MCU

3pcs 3-color Full Color LED SMD Module Board KY-009 5050 For Arduino MCU
3pcs 3-color Full Color LED SMD Module Board KY-009 5050 For Arduino MCU 3pcs 3-color Full Color LED SMD Module Board KY-009 5050 For Arduino MCU 3pcs 3-color Full Color LED SMD Module Board KY-009 5050 For Arduino MCU


Get 3pcs 3-color Full Color LED SMD Module Board KY-009 5050 For Arduino MCU


Overview:
 
The RGB LED module is made of a full-color LED chip. The PWM voltage input of the three pins R, G, and B can adjust the intensity of the three primary colors (red/blue/green) to achieve full-color color mixing. Cool lighting effects can be achieved with the control of the module.
 
Features:
 
1. Use 5050 full color LED
2. RGB three primary color connected to the current limiting resistor to prevent burnout
3. Adjust the three primary colors by PWM to get different colors
4. Can interface with various microcontrollers
5. Working voltage: 5V
6. LED drive mode: common negative drive

Package includes:

3 x Module
















3pcs 3-color Full Color LED SMD Module Board KY-009 5050 For Arduino MCU See detail


Popular posts from this blog

SPH0645 I2S MEMS Microphone Sensor Board SPH0645LM4H 1.6-3.6V For Arduino Raspberry Pi

Image
Get SPH0645 I2S MEMS Microphone Sensor Board SPH0645LM4H 1.6-3.6V For Arduino Raspberry Pi Description:   The microphone is a single mono element. You can select whether you want it to be on the Left or Right channel by connecting the Select pin to power or ground. If you need stereo, pick up two microphones!  You can set them up to be stereo by sharing the Clock, WS and Data lines but having one with Select to ground, and one with Select to high voltage. This I2S MEMS microphone is bottom ported, so make sure you have the hole in the bottom facing out towards the sounds you want to read. It's a 1.6-3.6V max device only, so not for use with 5V logic (its really unlikely you'd have a 5V-logic device with I2S anyways).  Many beginner microcontroller boards don't have I2S, so make sure its a supported interface before you try to wire it up! This microphone is best used with Cortex M-series chips like the for Arduino Zero, for Feathe...
Read more

QF1021-A-10M 0-10Min Adjustable 220V Time Delay Relay Module Timer Delay Switch Timed Off with Overcharge Protection

Image
Get QF1021-A-10M 0-10Min Adjustable 220V Time Delay Relay Module Timer Delay Switch Timed Off with Overcharge Protection Features:   - Relay load capacity up to 10A250V - 3W metal oxide film resistor, withstand voltage - Double Zener to improve stability - Using single chip delay, time precision - QF1021-A-10M: (Time out -off) Turns on immediately after power-on, the delay is automatically disconnected, up to 10 minutes   Specifications:   Delay adjustment resolution: 100 levels, that is, the minimum range of 100 minutes can be adjusted to 1 minute, 1 minute per division. Delay error: 2% Standby power consumption: 1.0W Load capacity: 10A250V (General motor can be connected to 800W or less, please take the starting current as the standard) PCB size: 58mm * 43mm, height <20mm   Applications:   Home appliances, lighting delay modification, factory equipment delay control.   Warmly Noted:   The whole board is equipped with 220V voltage....
Read more

150pcs Terminal Connector Direct-pin Bare Wire Connector Terminal

Image
Get 150pcs Terminal Connector Direct-pin Bare Wire Connector Terminal Specification:   Type: Terminal Working frequency: low frequency Application: Wire Cable Shape: Bar Characteristics: Fire resistance / Flame retardant Contact material: Copper Insulator material: Plastic Package includes:   1 x 150PCS JST-XH  Terminal Connector 2-5PIN 150pcs Terminal Connector Direct-pin Bare Wire Connector Terminal See detail
Read more