2pcs 3.5 Inch TFT Color Display Screen Module 320 X 480 Support Arduino UNO Mega2560

2pcs 3.5 Inch TFT Color Display Screen Module 320 X 480 Support Arduino UNO Mega2560
2pcs 3.5 Inch TFT Color Display Screen Module 320 X 480 Support Arduino UNO Mega2560 2pcs 3.5 Inch TFT Color Display Screen Module 320 X 480 Support Arduino UNO Mega2560 2pcs 3.5 Inch TFT Color Display Screen Module 320 X 480 Support Arduino UNO Mega2560


Get 2pcs 3.5 Inch TFT Color Display Screen Module 320 X 480 Support Arduino UNO Mega2560


Description:

Support Arduino UNO and Arduino Mega2560 and other development board DIP, Without any wiring, all open source, Arduino libraries offer
The backlight always on, can not control the backlight, backlight is connect to 3.3V
DC: 5V

More information: >>>>Click here<<<<

Note:

The control and driving circuit of TFT modules is low voltage and  FRIDA micro-power CMOS circuit, can be easily damaged by static, static damage is an irreparable damage, and sometimes human have hundreds of volts of high voltage static electricity, therefore, in handling, assembling and use should be extremely careful to prevent static electricity:　

1. Using soldering iron or  power FRIDA tools must be well grounded and operation, make them without leakage;
2. Do not use hand to touch the leads, circuit boards and metal boxes;
3. Do not use a vacuum cleaner for cleaning, because it generates strong static electricity;
4. When the air is dry, can also generate static electricity, therefore, workshop humidity  shall be above RH60%;
5. If it is necessary to direct contact it , should enable the human body in the same potential with the modules? ,ormake  human body be well grounded;
6. Remove or back in the bags or move locations, also need to be careful to prevent static electricity. Don't replace or discard the original packing.
 
Package included:

2 x 3.5 Inch TFT Color Screen Module 320 X 480 Support Arduino UNO Mega2560























2pcs 3.5 Inch TFT Color Display Screen Module 320 X 480 Support Arduino UNO Mega2560 See detail


Popular posts from this blog

SPH0645 I2S MEMS Microphone Sensor Board SPH0645LM4H 1.6-3.6V For Arduino Raspberry Pi

Image
Get SPH0645 I2S MEMS Microphone Sensor Board SPH0645LM4H 1.6-3.6V For Arduino Raspberry Pi Description:   The microphone is a single mono element. You can select whether you want it to be on the Left or Right channel by connecting the Select pin to power or ground. If you need stereo, pick up two microphones!  You can set them up to be stereo by sharing the Clock, WS and Data lines but having one with Select to ground, and one with Select to high voltage. This I2S MEMS microphone is bottom ported, so make sure you have the hole in the bottom facing out towards the sounds you want to read. It's a 1.6-3.6V max device only, so not for use with 5V logic (its really unlikely you'd have a 5V-logic device with I2S anyways).  Many beginner microcontroller boards don't have I2S, so make sure its a supported interface before you try to wire it up! This microphone is best used with Cortex M-series chips like the for Arduino Zero, for Feathe...
Read more

QF1021-A-10M 0-10Min Adjustable 220V Time Delay Relay Module Timer Delay Switch Timed Off with Overcharge Protection

Image
Get QF1021-A-10M 0-10Min Adjustable 220V Time Delay Relay Module Timer Delay Switch Timed Off with Overcharge Protection Features:   - Relay load capacity up to 10A250V - 3W metal oxide film resistor, withstand voltage - Double Zener to improve stability - Using single chip delay, time precision - QF1021-A-10M: (Time out -off) Turns on immediately after power-on, the delay is automatically disconnected, up to 10 minutes   Specifications:   Delay adjustment resolution: 100 levels, that is, the minimum range of 100 minutes can be adjusted to 1 minute, 1 minute per division. Delay error: 2% Standby power consumption: 1.0W Load capacity: 10A250V (General motor can be connected to 800W or less, please take the starting current as the standard) PCB size: 58mm * 43mm, height <20mm   Applications:   Home appliances, lighting delay modification, factory equipment delay control.   Warmly Noted:   The whole board is equipped with 220V voltage....
Read more

110-240V 500W Smart Home EU Dimmer Switch Crystal Glass Wireless Remote Control Light Dimmer Switch RF Switch 220V

Image
Get 110-240V 500W Smart Home EU Dimmer Switch Crystal Glass Wireless Remote Control Light Dimmer Switch RF Switch 220V Description: - Mechanical Life: 100,000 Times of Operation - Max. Voltage: AC 110~250V/50~60Hz - Max. Current: 6A - Size: 80*80*42mm - Color: White or Black - Panel material:  Crystal Termpered Glass Panel - Total Rated Load: 20-500W - Operating Environment: -10~50 Centigrade; Less than 95% RH - Self Consuming Power: Less than 0.1mW - Function: Touch and Dimmer Function - Touch left "Triangle sign"button, the light will become brighter; -Touch right "Triangle sign" button, the light will become weaker. Features: - Luxury Galss Panel, Combine Wall Switch With Fashion - Perfect flat plate, smooth gorgeous - Exquisite craftwork, well polished, luxurious experience - Capacitive touch sense, sensitive touch control, feeling like smart cell phone touch - Backlight indicator, luminated more considerate - Installa...
Read more